Tinting car windows at home

Make sure you have window cleaner, certified roll of window tint film, spray bottle of hot water, small hand squeegee,. On the other end, a tinting film of 20 percent will be nearly completely black. You may need to pull the seal back with your fingers and use the edge to tuck at the same time. This is how you can do it yourself and tint your own car windows on your own time. Some states allow darkly tinted windows in the back, but not in the front of the vehicle.

To prevent tearing, continue spraying the film as you work out air bubbles. Solar tinting, security tinting, and decorative tinting. To keep the interior of your car, home or office more comfortable. Once you have the tint by itself, proceed to spray the interior of the car window with the film application solution.

Some states do not allow certain levels of tint, especially black outs. Car window tint and home or office window tint both have the same purpose; Check out these tips for window tinting your car. How to establish a business tinting car windows from home. Car window tint is designed to shrink to fit the curves of automotive windows.

As a first step, consider visiting a window tinting shop and learn about the several. Now spray the sticky side of the tint with the solution as well. Wash or clean the windows completely before tinting. Using the squeegee or applicator, carefully tuck exposed edges of the film under the window seals.

Any car models from acuras to bmw's look super sleek with a mad tint job. Applying the film once you are satisfied that the film will fit the window, apply a generous amount of application solution with a squeeze, or trigger spray bottle, and peel the protective layer off the tint film, and spray the. Use your fingers and your card or hard edge to tuck the tint into the bottom edge of the window seal. Again, use the tint squeegee to push out all the water and air bubbles from under the film.

Make sure you get all the edges and seals, and role the window up to get the bottom. You're going to need almost a gallon of soapy water throughout this process. Prepare the water ahead of time to make working easier. A spray bottle is highly recommended. Take a clean rag and dry the window. Wipe away the soapy water on both sides and dry off the edges as well. If you're using a spray bottle, refill it with more soapy water.

A squeegee will help you get the window completely dry. Make sure you get underneath the seals in the interior of the car. Use your finger to get under the seal and remove dirt and dust. Roll the window back up before beginning, but leave your car on. You'll need to move the window up and down as you work. For now, leave it up. Determine which side of the tint is adhesive. Like a sticker, the tint has a layer that can be peeled off right before adhering it to the window.

Make sure, as you work with the tint, that this side is facing you. Part 2. Spray the outside of the window with soapy water. The water will help the tinting temporarily adhere, but still make it slippery enough to slide around and put into place. Place the tinting over the outside of the window so that it covers the entire window.

Unroll your tinting so that it covers the entire window, with at least " of extra tinting over the edges. The liner the part that will later adhere to the window , should be facing you. Make sure you do not remove the liner -- you're just sizing and pressing the tinting right now, now adhering it. Cut away a manageable slab of tinting. You should have a few inches of extra tint in every direction, but you don't want to be maneuvering the entire roll of film while working.

Use a precision knife or blade to cut a usable square of tinting film from the larger role. Spray the front of the film with water. Once the tint is cut into a square, it should stick to the water on the outside of the window. You should then spray the tint itself so that the entire thing is covered in a thin layer of soapy water. Take your knife and cut along the bottom and left edges of the window.

Simply use the edges of the window to trace your knife across the tinting film. You want a perfectly shaped line to ensure the tint fits. When done, two of the edges should fit perfectly, and the rest should still be square. As you cut, use the squeegee or your free hand to make sure the film is flush with the window. When done, cut the excess film away and discard.

Pull the film 1" towards the left edge. You want to shift the film towards the edge you just cut. This ensures that you have enough tint to cover every edge of the window, including the part covered by the seal. Cut the right edge, then slide the tint halfway back towards the center. Pull the film down roughly one inch, so the bottom edge is lower than the window.

This is the tint that will eventually go into the door, allowing you a better light seal. Slide it down and then use the squeegee to flatten it again. You'll be doing the same thing you just did with the right and left side on the top and bottom edges. Lower the window a half inch, then use the top of the window to cut the film to shape.

Once the window is lowered, you can use this top edge of the window as your guide. Use the precision knife to cut right to the top of the window. When done, pull the tint back towards the center. Clean up any of the corners that have excess film. When cutting away, the corners may have bits and pieces of extra film in the corners.

Use your knife to clean it all up. Realign your film so that it fits the window perfectly, with some excess on every edge. You may need to reapply water to make it stick. Working toward the sides and top, use the tint squeegee to push out water and air bubbles. Spray the window down with soapy water.

Where i live it is helpful to prevent the sun fading furniture, drapes, etc. These advances in technology now allow for window films that can block a significant amount of heat energy while still allowing the homeowner to enjoy a virtually unimpaired view from the window.

Write down your findings and then measure a second time to make sure your measurements are correct. A home window tint, also known as solar window film, is a thin layer similar to what you find on car windows. And it may actually help with cooling costs in the summer! Home window tinting reduces heating and cooling bills, reduces incoming uv light, and prevents the fading of window treatments and home furnishings. Like car window tint, it can help block out ultraviolet rays from the sun, helping to control the flow of heat through your windows.

Remove the backing from the window tint and place it on the window you are planning on tinting. It is important to keep the tint moist in order to move it around the area and remove any. There's a bit of a learning curve, so start with a small area and follow. Spray the top of the window tint with more soapy water.