Installing plank paneling

Measure walls, check for level and square. Depending on dimensions and room construction, you may need to trim some panels accordingly. Depending on your project, when fitting for dry layout, planks can be centered at a focal point, such as behind a sink or the center of a room. For the purpose of the layout only, build out from both sides of the focal point, to ensure how the planks fit into the space.

Add a bead of the sealant along recently cut edges to be placed into the corner. Repeat this process on perpendicular plank also facing corner image B. Cut Palisade planks by scoring and snapping with a utility knife.

This method may require sanding the snapped edges. You can also use standard wood working tools like a table saw or circular saw with a fine-tooth blade to provide a clean, smooth cut image E. Use a tooth blade or higher. Cut planks for outlets and light switches.

Measure and mark the borders where the opening will be with a marker. Use a jigsaw to cut the remaining opening, following your tracing image G. Do not attach accessories like coat hooks, light fittings, mirrors, etc. Drill holes through the tiles and use suitable anchors to attach the accessories securely into the framing behind. Seal per sealant instructions. If you choose to finish the edges, we recommend our matching trim for both end pieces and inside corners.

We recommend using baseboard or cove molding to finish the bottom row, regardless of flooring material. For both end trim pieces and corner trims, install trim in appropriate location prior to setting plank into trim image H. This will prevent any moisture buildup. If your project calls for Palisade planks starting at a floor, be sure the first row is straight and level.

Determine the desired height of your first plank row and snap or draw a level line at that height for a reference line. Align the tops of each plank in the first row to the snapped line image J. It is important that this starting row be level and straight. If you are starting with full tile, cut off the tongue or use a matching J-trim along the bottom edge.

To install your first plank, begin with bottom row. Make sure the first plank you intend to install fits properly and is level. You may need to place a temporary shim under each bottom plank to hold them in place while the adhesive sets image K. Apply adhesive to the back of the plank. Apply the plank to the substrate by pressing it into place. Apply even pressure with your hands across the entire plank.

If necessary, use shims or pins to hold planks in place until the adhesive sets. Wipe off excess adhesive. Use water and a cloth. Clean off any adhesive residue that is visible while it is still wet.

Do not allow this residue to dry as it will be difficult to clean up when dry and could damage the finish. Repeat until bottom row is complete. If installing in a corner, cut off the flange facing the corner to allow a plumb surface against the substrate.

Repeat this process on plank that abuts the previous one also facing the corner. Allow the adhesive on the bottom row to set up so that all subsequent rows remain level.

Determine what pattern you want to use before starting the second row MP image N, O. Commonly-used options are running bond vertical joints are staggered and stack bond vertical joints line up.

After the first row has set up, apply the remaining tiles according to the pattern or layout you desire. Use adhesive and methods described above for remaining rows. When installing the top row, install as you have been until you get to the last plank in the corner.

If planks butt against your ceiling, when installing the last plank, remove flanges from side image O. Or use our matching L trim. Lay plank into place. Apply pressure to ensure it is flush with others. Use a recommended silicone sealer as previously described in joints to ensure a water-tight installation, if applicable.

Read and follow if your project looks like this. The challenge is to place the remaining plank section into the edge trim while also getting the interlocking plank edges locked together image P. First, install the inside corner trims into each corner using adhesive.

We did this to make sure it fit properly, this method is called dry-fit. Step 3 : We then turned the paneling face down and applied glue to the back of the paneling.

Note : We used glue and nails to attach the paneling to the walls. Depending on the surface, nails can be used on their own as well. And same for glue, it can used on its own. Step 4 : We put the paneling back against the wall placing a level on the top to make sure it was level. Then we pressed it firmly into place. Step 5 : Using our nail gun, to secure the paneling even more to the wall, we nailed each end of the paneling as well as the middle. Step 6 : Time to add the second piece.

We dry fitted the next piece making sure it attached correctly to the previous piece. Step 8 : We inserted the second piece into the first piece by inserting the groove into the tongue of the previous piece.

Then we pressed it firmly against the wall. Step 10 : We continued following the above steps until we had planked the wall up to where the shelves were. Step 11 : We also planked the sides of the closet leaving space to add a thick piece of wood. The piece of wood served as the support for the shelves and to attach the closet rod.

Note : Unlike the main wall we did have to cut the paneling for the side walls. To do so, we used our miter saw. Step 12 : To fill the corner gaps between the back planked wall and the planked sides, we added corner moulding. We just LOVE how it turned out! Just a question of measuring, cut the pieces, fastening them to the wall, and then move on to the next pieces. Depending on the type of surface that is being covered with wood paneling, glue can be used on its own and the same thing for nails.

Read the packaging on the wood paneling, it will tell you which method is recommended for each type of surface. As an Amazon Associate and member of other affiliate programs, I earn from qualifying purchases. This site uses Akismet to reduce spam. Learn how your comment data is processed. Pinterest Facebook Twitter Reddit Email.

Materials Wood paneling 8ft v-joint rustic grade paneling made of eastern white wood Paneling adhesive. Tools Level Caulk gun Nail gun Miter saw. Instructions Before starting installation, remove paneling from packaging. Acclimate the wood paneling in the location it will be installed for a minimum of 72 hours. Dry fit the first piece of wood paneling on the wall, with the groove pointing down and the tongue pointing up. If the piece is too long, cut it to size.

Apply adhesive behind the wood panel.