Ariens 8524 snowblower manual

Re-assemble the housing in re-verse order. To replace the tractor drive belt you now need to pull the idler and remove the belt from the sheave.

Once done activate the clutch and verify that machine works normally. If it is working hard you can additionally pull back the blower back idler arm clevis pin. In order to replace the snowblower housing you need to place the housing on the rod and securely tip the tractor and the blower together while holding the drive belt in up position.

Use two cap screws to secure onto a frame. Tighten the screws while holding the handlebars up. Attachment belt should be rolled on the engine shave. Roll the belt under the belt finger into place while pulling the recoil starter rope. Adjust if necessary. Verify that attachment belt and sheave are in alignment. Re-align if necessary. Do the same with blower sheave and break pads, Re-align is necessary. If belt slips it will need adjustment, that can be made by adjusting the idler in the idler arm slot- that can result in higher belt tension.

Remember that when attachment clutch is disengaged, the belt should clutch. Replace the belt and crank parts, spark wire and readjust the chute crank. In order to replace the friction wheel you need to first tip the machine to service position and secure it properly. Then you should set the speed selector to first position. Once done disengage the traction clutch lever in order to not to hold the friction wheel. Loosen and remove all the bolts fixing the the wheel to the hub.

Put speed selector to third position and disconnect the shift link. Install new friction wheel on the hub and replace or use old bolts to fix the wheel.

Tighten, you can replace the bottom cover if that is severely worn too. Snowblowers as any other household machinery is really used everyday. In most cases it is being used seasonally so it requires special storage in order to work properly though many seasons. Allow engine and all other parts to cool down before putting to storage place. Remember that your local Ariens service dealer is the best point of contact when it comes to troubleshooting your machine.

With any questions or concerns you should first turn to them. Professional, Compact, Platinum and Deluxe. Troubleshooting Manual Safety first! Before operating or troubleshooting your Ariens snowblower follow the safety rules first as not proper snowblowers handling can result in severe damage or death of not only operator but also people in close area: you should never inhale gases coming from snowblower exhaust, no adjustments to emission controls should ever be done always disengage the auger, engine and stop unit, remove the key and wait for all moving parts to stop before you leave the snowblower.

Moving parts are able to amputee or crush body parts modern snowblowers are equipped with number of decals. Ariens Snowblower controls There are number of tools that allow snowblower controls.

Service and maintenance Like any other snowblowers, xanaxbars. Following actions will be handled, checked and fixed at the service station: operation of the clutch lever fasteners adjustment dual handle interlock clutch cable adjustments engine oil exchange machine lubrication tire pressure Ariens snowblowers troubleshooting Table 1.

Possible cause. Belt squeals continuously. Frozen impeller, attachment clutch needs adjustment. Move snowblower to warm area, adjust the clutch. A lot of now left behind. Worn or damaged blade scraper. Machine pull to the one of sides. Scraper blade or skid shoes need adjustment. Adjust as necessary. Small rubber pieces collected in frame. Friction disk wear. Replace in service station. Shear bolts are broken. Replace shear bolts. Frozen impeller. Move snowblower to warm area or replace impeller.

Break not adjusted correctly. Adjust break per operators manual. Sth is obstructing the auger. Remove obstuction while engine is switched off. Auger drive belt worn or damaged. Pulley-V 8. Ariens 8 oz. Washer, Fiber.

Seal 1. Bushing-Flanged 1. Speed Selector And Frame. Bolt, Rdhdsqnk. Screw, Tapping x. Washer, Saddle-. Page I. Knob, Ball-Black 1. Nut, Locking Wing. Nut, Locking Nylon. Page J. Page K. Idler-Flat 3.

Idler-V 3. Popular Parts. Shear Bolt. Round Head Square Bolt. Flanged Whizlock Nut. Friction Wheel. Pin, Spring Clip.

Snowblower Parts. Repair Guides. How to Replace a Shear Pin on a Two-Stage Snowblower This video outlines the simple steps required to replace a shear pin on your two-stage snowblower. Quick Fix: How to Replace the Spark Plug in a Small Engine This video will help you replace the spark plug on a small engine which will help get your gas powered equipment up and running again.

How to Adjust the Skid Plates and Scraper on a Two-Stage Snowblower With this video, you can quickly learn how to adjust your snowblower's skid shoes and scraper to improve performance and prevent damage. Accessories for the Ariens No questions have been asked yet. Ask a question. Ask our experts a question about this part and we will respond as soon as we can. Join our VIP email list to receive money-saving-advice and special discounts.

Model Number Recommended. Submit your question. Thank you for your question! Review Limited Warranty Policy. Keep clear of auger while engine is running. Page 9: Safety Rules Stop engine, remove key, read manual before making any repairs, adjustments. OL Wear appropriate hearing protection. OL 3. Stop engine and remove key before clearing. High speed impeller rotates below discharge opening. Wait for all moving parts to stop before removing clogs or OS servicing. Page 10 Fumes from engine exhaust can cause injury or death.

DO NOT run engine in an enclosed area. Always provide good ventilation. When practical, remove gas-powered equipment from the truck or trailer and refuel it on the ground. Read and understand the entire Safety section before proceeding.

Page 13 1. Pinion Bracket 7. Mounting Nut 2. Gear Strap 8. Flat Gear 3. Chute Bracket 9. Pinion 4. Retainer Clip Chute Strap 5. Lower Ring Universal Joint 6. Chute Ring Page Operation 1. Cable Eye 2. Flat Washer and E-Ring 3. Release attachment clutch lever. Attachment clutch should remain engaged until traction clutch lever is released, then both clutches must disengage. Release both clutch levers 2 to disengage power and apply brake to attachment.

DO NOT throw snow any higher than necessary. Page Filling Fuel Tank Scraper Blade The scraper blade allows the back of the housing to keep better contact with the surface being cleared.