Yamaha receiver rx-v420 manual

The research, engineering, and. Modifications are, therefore, inevitable. Should any discrepancy appear to exist, please. To Service Personnel Impedance Selector Front Panels Remote Control Transmitter Rear Panels Internal View Disassembly Procedures Failure to follow appropriate service and safety procedures when servicing this product may result in personal.

For these reasons,. The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or. Static discharges can destroy expensive components.

Discharge any static electricity your body may have. Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit. Self Diagnosis Function Diag Amp Adjustment S Display Data Ic Data Block Diagram Do you have a question about the Yamaha RX-V or do you need help? Ask your question here. Provide a clear and comprehensive description of the issue and your question.

The more detail you provide for your issue and question, the easier it will be for other Yamaha RX-V owners to properly answer your question. View the manual for the Yamaha RX-V here, for free. This manual comes under the category Receivers and has been rated by 3 people with an average of a 8. This manual is available in the following languages: English. Is your question not listed? For these reasons,. The data provided is believed to be accurate and applicable to the unit s indicated on the cover.

The research, engineering, and. Modifications are, therefore, inevitable. Should any discrepancy appear to exist, ple ase. The name of the selected program appears on the display. Press this button to turn on or off the effect speakers center and rear. In that case, the output levels of the right and left speakers may not match. Connect an auxiliary audio or video input source such as a game console or camcorder to these jacks. To reproduce source signals from these jacks, select V-AUX as the input source.

This button is used to select a preset station number 1 to 8. Press lto select a lower and hto select a higher preset station number. This button is used for tuning.

Press lto tune in to lower frequencies, and hto tune in to higher frequencies. This button is also used to exchange the assignment of two preset stations with each other. Press this button to store the broadcasting stations. Hold down this button for more than 3 seconds to begin automatic preset tuning for FM stations only. Press this button to switch the tuning mode between automatic and manual.

The name of the selected input source appears on the display. This section describes basic operation of this unit with the remote control. Each time you press this button, the unit switches between the power on and standby mode.

This flashes in red when pressing a button on the remote control. If it flashes rapidly several times, press the selected button again. Press one of these buttons which corresponds to the component you want to control with the remote control.

The proper code must be set for your component. When the component selector button has been pressed, the remote control is set to that component operation mode. These buttons are used to select a preset station.

The remote control transmits a directional infrared beam. Be sure to aim the remote control directly at the infrared sensor during operation. When the sensor is covered or there is a large object between the remote control and the sensor, the sensor cannot receive signals. The sensor may not be able to receive signals properly when it is exposed to direct sunlight or a strong artificial light such as a fluorescent or strobe light.

In this case, change the direction of the light or reposition the unit to avoid direct lighting. This lights up when this unit is reproducing PCM pulse code modulation digital audio signals.

This display shows various information: for example the name of the selected input source and the various settings during adjustment with the SET MENU. The current station frequency and band FM or AM also appear when the tuner is selected as the input source.

This lights up when an FM stereo broadcast with sufficient signal strength is being received. During this period, the displayed station can be stored in the memory. Use this switch to match the amplifier output to your speaker impedance. Set this unit in the standby mode before you change the setting of this switch see page This unit is designed to provide the best sound-field quality with a 5-speaker system, using main speakers, rear speakers and a center speaker. If you use different brands of speakers with different tonal qualities in your system, the tone of a moving human voice and other types of sound may not shift smoothly.

We recommend that you use speakers from the same manufacture to ensure even tonal quality. The main speakers are used for the main source sound plus the effect sounds. They will probably be the speakers from your present stereo system.

The rear speakers are used for the effect and surround sounds, and the center speaker is for the center sounds dialog, vocals, etc.

If for some reason it is not practical to use a center speaker, you can do without it. Best results, however, are obtained with the full system.

The main speakers should be high-performance models and have enough power-handling capacity to accept the maximum output of your audio system. The other speakers do not have to be equal to the main speakers. For precise sound localization, however, it is ideal to use highperformance models that can reproduce sounds over the full range for the center speaker and the rear speakers.

It is also possible to further expand your system with the addition of a subwoofer. The use of a subwoofer is effective not only for reinforcing bass frequencies from any or all channels, but also for reproducing the LFE low frequency effect channel with high fidelity when playing back a source encoded with Dolby Digital or DTS.

Place the right and left main speakers an equal distance from the ideal listening position. The distance of each speaker from each side of the TV monitor should be the same. Place these speakers behind your listening position, facing slightly inwards, nearly 1. Align the front face of the center speaker with the front face of your TV monitor. Place the speaker as close to the monitor as possible, such as directly over or under the monitor and centrally between the main speakers.

The position of the subwoofer is not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer near the main speakers. Turn it slightly toward the center of the room to reduce the wall reflections. Please use magnetically shielded speakers. Sometimes a video monitor may be adversely affected even when magnetically shielded speakers are used.

Never connect this unit and other components to mains power until all connections between components have been completed. Some components require different connection methods and have different terminal names. Refer to the instructions for each component to be connected to this unit. After completing all connections, check them again to make sure they are correct.

This unit has digital jacks for direct transmission of digital signals through either coaxial or fiber optic cables.

All digital input jacks are acceptable for kHz sampling digital signals. When making connections between the digital signal jacks, you should connect the components to the same-named analog audio signal jacks of this unit, because a digital signal cannot be recorded by a recording component connected to this unit.

Pull out the cap from the optical jack before you connect the fiber optic cable. Do not discard the cap. When you are not using the optical jack, be sure to put the cap back in place.

This cap protects the jack from dust. If you use a fiber optic cable that does not conform to this standard, this unit may not function properly. When you connect your recording component to both the analog and digital input and output jacks, the priority is given to the digital signal.